vacuum deaerator specification in boiler
HOT
Capacity:1-20t/h
Rated thermal efficiency: 100-104%
Fixed working pressure: ≤1.6MPa
Applicable fuel:natural gas etc.
HOT
Capacity:0.7-14MW
Rated thermal efficiency:96-98%
Fixed working pressure:≤1.25MPa
Applicable fuel:Natural gas, light oil, etc.
HOT
Capacity:0.7-2.8Mw
Rated thermal efficiency: 97.2-106%
Fixed working pressure:0.1MPa
Applicable fuel:Natural gas, etc.
HOT
Capacity:2.8-7.0Mw
Rated thermal efficiency:≥105.5%
Fixed working pressure:-0.02MPa
Applicable fuel:Natural gas, etc.
HOT
Capacity:99Kw
Rated thermal efficiency:97.2-104.4%
Fixed working pressure:1.0MPa
Applicable fuel:Natural gas, etc.
HOT
Capacity:0.5-4.0 t/h
Rated thermal efficiency:98%
Fixed working pressure:≤1.25MPa
Applicable fuel:electric energy
As shown in Figure 35-17, a steam generating system includes three major components for which treatment is required: the deaerator, the boiler, and the condensate system. Oxygen scavengers are usually fed to the storage section of the deaerator. The boiler internal treatment is fed to the feedwater pump suction or discharge, or to the steam drum.Get Price
The boiler feedwater pumps normally take suction from the deaerator storage tank, discharge to the feedwater heaters, and then supply the boiler. Here, too, the designer has to deal with the possibility of flashing fluid and must ensure that the deaerator storage tank is located at an elevation that will provide sufficient net positive suction Get Price
- Direct steam-type humidifiers inject boiler-generated steam directly into the air stream. These systems normally operate above 70 degrees C (158 degrees F), and Legionella cannot survive at that temperature. - Atomizing humidifiers use mechanical devices or pneumatic air to create a water mist that evaporates into the air stream.Get Price
The boiler feedwater pumps normally take suction from the deaerator storage tank, discharge to the feedwater heaters, and then supply the boiler. Here, too, the designer has to deal with the possibility of flashing fluid and must ensure that the deaerator storage tank is located at an elevation that will provide sufficient net positive suction Get Price
Water leaks, cracks, or rupture of the boiler and/or boiler sections * NOTE: If a part covered under your Residential Natural Gas Furnace Plan is replaced while in use as a component of an electric central air conditioner, you will be charged the current diagnostic fee …Get Price
Where hot-water-heating boilers are connected to heating coils located in air-handling units where they can be exposed to refrigerated air circulation, such boiler piping systems shall be equipped with flow control valves or other automatic means to prevent gravity circulation of the boiler water during the cooling cycle. [NFPA 54:10.3.9.2]Get Price
- Direct steam-type humidifiers inject boiler-generated steam directly into the air stream. These systems normally operate above 70 degrees C (158 degrees F), and Legionella cannot survive at that temperature. - Atomizing humidifiers use mechanical devices or pneumatic air to create a water mist that evaporates into the air stream.Get Price
As shown in Figure 35-17, a steam generating system includes three major components for which treatment is required: the deaerator, the boiler, and the condensate system. Oxygen scavengers are usually fed to the storage section of the deaerator. The boiler internal treatment is fed to the feedwater pump suction or discharge, or to the steam drum.Get Price
- Direct steam-type humidifiers inject boiler-generated steam directly into the air stream. These systems normally operate above 70 degrees C (158 degrees F), and Legionella cannot survive at that temperature. - Atomizing humidifiers use mechanical devices or pneumatic air to create a water mist that evaporates into the air stream.Get Price
As shown in Figure 35-17, a steam generating system includes three major components for which treatment is required: the deaerator, the boiler, and the condensate system. Oxygen scavengers are usually fed to the storage section of the deaerator. The boiler internal treatment is fed to the feedwater pump suction or discharge, or to the steam drum.Get Price
The boiler feedwater pumps normally take suction from the deaerator storage tank, discharge to the feedwater heaters, and then supply the boiler. Here, too, the designer has to deal with the possibility of flashing fluid and must ensure that the deaerator storage tank is located at an elevation that will provide sufficient net positive suction Get Price
Feel free to reach out if you want to collaborate with us, or simply have a chat.
